广州捶打水冷式粉碎机

广州捶打水冷式粉碎机用途 产品介绍：  

Water mill-water-cooled universal mill parameter name:

      粉碎机（不锈钢粉碎机）、高效粉碎机、食品粉碎机、高速粉碎机、多功能粉碎机、化工粉碎机、制剂粉碎机，适用于食品、制药、化工等行业的物料粉碎之用。禁用于粉碎易燃易爆品。

     Universal mill (stainless steel universal mill), efficient mill, food mill, high-speed universal grinder, multi-functional grinder, grinder mill, preparations of chemical industry, for food, pharmaceutical, chemical and other industries of crushing purposes. Banned inflammable and explosive products used to crush.

  聂

  广州捶打水冷式粉碎机结构简洁、坚固，运转平稳，粉碎物料快速、均匀，效果良好。本机全为不锈钢材料制作，机壳内部（粉碎槽）所有齿槽经精密机加工从而达到表面平滑，易于清理，改变了普通粉碎机内壁粗糙、易积粉、难清理的现象，使食品、药品、化工等生产更能符合国家标准，达到GMP的卫生要求。  

     Water mill-water-cooled universal mill parameter structure is simple, strong, smooth, crush the material quickly and evenly, with good results. This machine is all stainless steel, casing (crush Groove) all alveolar precision machining so as to achieve a smooth surface, easy to clean, change within the General mill coarseness, easy to accumulate powder, hard to clean, so that food, medicine, and chemical production more in line with national standards, meet the GMP requirements.  

技术参数：

广州捶打水冷式粉碎机工作原理：

Parameters of water mill-water-cooled universal mill working principle:

     本机粉碎原理锤式回风高速粉碎。粉碎物可直接从磨腔中排出，经出料口出来，一般的物料经过粉碎后要经过棉布袋来收集，粉碎后的物料收集在袋内，空气则从布袋的细小孔眼出来，不会将细粉排出，从而起到不浪费，不污染的效果。粒度大小由更换不同目数的筛网决定。

     Principles of native smashing hammer high-speed Smash in return. Crushed can be directly discharged from the grinding Chamber, outlet, and generic material after crushing to cotton bags collected, crushed material collected in the bag, the air from the bag out of the small hole of, fines will not be discharged, so as to not waste and pollution effects. Grain size determined by the replacement of different mesh sieve.

     我司所研制生产的粉碎机是采用优质304号不锈钢制作，配套国标电机，主要用于化工材料、中药材含树根、树枝以及块状类物料、各种含油量不高的粮食、五谷杂粮以及其他一些硬性、脆性的物料。

     We develop and produce universal mill is made of high quality stainless steel No. 304, and supporting standard motors, mainly used in chemical materials, herb roots, branches and bulk material of low oil content, a variety of food, grains and other hard, brittle material.

特别注意：不得粉碎金属,特坚固及高粘度物料.

Special Note: not crushing metal, sturdy and high-viscosity materials.

广州捶打水冷式粉碎机安装、操作和维修保养：

Parameters of water mill-water-cooled universal mill installation, operation and maintenance of:

1、开机前必须检查门是否关紧，关紧门时要拧紧手轮和定位螺栓。

Before 1, boot, you must check that the door is closed, close the door to tighten the hand wheel and the lock bolt.

2、接通水冷却装置，保证水源充足，运行是严禁断水。

2, connect the water cooling, guarantee adequate water, running water is strictly prohibited.

安装时，接通电源，以电动方式检查电机旋转方向是否按标箭头方向。如相反，请调整电机接线盒接线。

3, installation, switch on the power, with electric check motor rotation direction according to the direction of the arrow. Instead, adjust the motor junction box wiring.

4、在电机旋转方向正确的情况下，开机空运转30分钟，检查润滑情况，及时加润滑油脂。定期检查和补充润滑油脂。

4, in the case of motor rotation direction is correct, boot time 30 minutes, check the lubrication, plus lubricating grease in a timely manner. Regularly check and supplement the lubricating grease.

5、进料前空运转数分钟，然后缓慢均匀地加料，切勿加满料斗，并注意电流是否超负荷，防止损坏设备。

No-load operation for a few minutes before 5, feed, and then slowly feed evenly, do not fill the hopper and note whether current overload and prevent damage to equipment.

6、运转中如有巨大振动及噪音等不良情况，要及时关机检查。

6, operation, such as a huge vibration and noise and other adverse situations, to shutdown checks in a timely manner.

7、经常保持机件润滑、清洁，发现故障、缺陷及时修复或更换。

7, keep lubricate, clean, find fault, defects to repair or replace.